为阻碍打标机通过使用寿命，的进步史诗装备通过率和无缺率，压减缺♏点(dian♈)率。现将我单位打标机30岁的男人庇护及保养知识与法师讲解。
In order to prolong the service life of the jet printer, improve the utilization rate and intact rate of the equipmen♊t, and reduce the failure rate. Now we share our dailꦛy maintenance and maintenance knowledge with you.
一、喷码机平常利用注重事变：
1. Notices for the daily use of jet printers:
1、因打标机采用的印刷油墨和浓缩造成剂很是随便熄火，言于须在出色通风处安顿好打标机，一别易燃易爆、火炎和静(jing🎶)电放电。
1. Because the ink and diluent used in the jet printer are very easy to burn, it is 🌊necessary to🍃 place the jet printer in a well-ventilated place, away from fire, flame and static electricity.
2、也不༺(bu)要遗留下来uv油墨、洗濯剂净泡过的碎布和碎纸条在激光打码机旁。
2. Do not leave any ink, cloth and paper pieces soaked in detergent beside the printe🐟r.
3、 禁止在ꦆ(zai)手持打码机两侧抽食烟，应吊件“避免炊火”和“易然胶印油墨”标示在手持打码机两侧。
3. Smoking is strictly prohibited near the printer. The signs of "No Fireworks" ꧂and "Flammable Ink" should be hung near the printer.
4、在喷码器四个星期具体安🍌(an)排二被氧化碳灭武器（类比远接连10米）。
4. Place a carꦍbon dioxide fire extinguisher near the jet printer (the longestꦍ distance is 10 meters).
二、喷码电机的气毗连着重事变
I✨I. Notices for Electrical Connection of Jet Coder
1、 挂断220V某一项交流电压（含地线），需求巧用正厂交流电压线，毗连到劳固的(d🔥e)、器有地(d♛i)(di)线的交流电压墙壁插座上。
1. When connected to 220V single power supply ✅(i🔴ncluding ground wire), the original power supply cable must be used and connected to a fixed power socket with ground wire.
2、 地线的毗连须得遵照执行关于 按照(𝔉zhao)。要是地线开战不好的，有并能型成喷码器显卡的损伤或诱发别人的替伏可能性。
2. T♍he connection of ground wires must comply with the relevant regulations of the state. If the ground wire contact is not good, it may cause damage to the printer motherboard 🅰or other potential hazards.
三、往常保護养护要注意事变
3. Daily maintenance matters needing attention
1. 运用喷码(ma)器喷墨墨水、高浓剂时对阻止配戴隐性框架眼镜。
1. It is a🔜bsolutely forbidden to wear contact lenses when using ink and diluent of jet printer.
2. 当增多喷墨墨水或浓缩提炼剂使用时，倡导使用抗溶液拳套和(h💟e)防范镜。
2. Anti-solvent gloves and pro꧙tective goggles are recommended when adding i💮nk or diluent.
3. 手持喷码(ma)机一般怡养多线程下类：
3. T♔he daily maintenance process of the jet printer is a🅺s follows:
背景喷🃏码器保护英文养护首先是内部管道、旋转喷头养(ya🎃ng)护：
Maintenance of Beijing Printer is mainly pipeline and nozzle ♊maintenance.
a) 打印图片油墨升级更行：先将管线里的打印图片油墨全数抽暇，精提剂植入打印图片油墨罐运行的1h后全数 孤立，第三参与精提剂运行的0.5h后全数孤立，参与trw打印图片油墨。号召机戒每回收利用率两年停下做次打印图片油墨升级更行，有效保障武器运行的双倍不会改变。（抽取的废渣不号召第二次回收利用率，以可以防止进行管线梗塞） a) 洒水旋转水嘴洗濯：对不存在拒绝洗濯攻效的打码机，号召每天都触点开断电时洗濯，以 保障机获取高思想品德的打印图片可是。在洒水旋转水嘴左下角让容器类，用通用洗小瓶装入精提剂，盯准喷水嘴、电池充电极、探测极、各类高压偏转板上的墨渍停下洗濯，关注着不要再让精𝕴提剂溅出口眼及皮肤吧，洗濯清潔后，用卫生纸将洒水旋转水嘴各元件的洗濯剂沥干。
(a) Ink renewal: first, all the ink in the pipeline is exhausted, diluent is injected into the ink tank for 1 hour, then all the ink is discharged after adding diluent for 0.5 hours, and then the original ink is added. It is suggested that the machine be updated once a year to ensure more stable operation of the equipment. (Waste liquid extracted is not recommended for secondary use in order to avoid pipeline blockage.) a) Sprinkler cleaning: For the sprinkler without automatic cleaning function, it is꧋ recommended that the machine be cleaned when switched on and off every day to ensure high quality printing effect. First, place the container under the sprinkler head, fill the diluent with a special bottle, clean the ink stains on the nozzle, charging electrode, detection electrode and high-pressure deflection board. Take care not to let the diluent splash into the eyes and skin. After cleaning, wipe the cleaning agent of all parts of the sprinkler head with a paper towel.
b) 调济墨线：若发名墨线偏斜收受接手器，消停高压喷水嘴买通，用公供🌱洗瓶干预少 许精提剂至高压喷水嘴帽，频繁买通3次摆弄，如墨(mo♔)(mo)线直在一致的整体素质则需消停劳务报酬所得条理喷腔。墨线规程：对着收受接手器检查，墨线喷入收受接手器两分最为处且略左。（侧看墨线在收受接手器正重点）
B) Adjust ink line: If the ink line deviates from the reclaimer, the nozzle ജshould be opened first, a little diluent sౠhould be added to the nozzle cap with a special washing bottle, and the nozzle cap should be opened three times or so repeatedly. If the ink line is always in the same position, the nozzle cavity should be adjusted artificially. Ink standard: Looking at the recycler, ink is sprayed into one third of the recycler and slightly left. (Look sideways at the ink line in the middle of the receiver)
二）激光打码(ma)机永劫间停用后的保护措施 某些连续停用，没有时会是否，只需该激光打码(ma)机在每一周内开机黑屏行驶2次，并翻来墨线至少续展行驶或uv墨水更行另一个分钟，这样便(b💫ian)会用🦹多大次短停用截取永劫间的停用。
2) Maintenance of any downtime of the jet printer after a long dow🐬ntime, regardless of the length of time, as long 🅠as the jet printer runs twice a week, and opens the ink line to run continuously or ink updates for at least one hour, it can replace the long downtime with several short downtime.
1）打标机暂停服务时(ไshi)为8-60天：对喉管和旋转打印机喷(p🍷en)头中止两次洗濯，旋转打印机喷头朝上分配，严防油墨逆流。
1) Inkjet printer shutdown time is 8-15 days: the throat an🌜d nozzle are cleaned once, the nozzle is placed upward to prevent ink reflux.
2）打标机停止𓃲设备运作同时跨越式十天：这段时间可以将机制内的打印黑墨水排放口后插足精炼剂运作，终了后把打印机喷头朝上确定，必免打印黑墨水流失。
2) The stop time of the printer is more than 15 days. At this time, the ink in the machine must be discharged and run with diluent. After that, the sprinkﷺler head should be placed upward to prevent the ink from flowing back.
3）永劫间关机后加载打标机关注事变 关机8-30来天打标机的加载，若有需，查检一番墨线⭕不会改变形。中断一个4分鐘的(♋de)激光喷嘴买通。
3) Start t🍨he printer after a long downtime. Notes: Start the printer 8-30 days after the downtime. If necessary, check th🉐e stability of the ink line. Make a 5-minute nozzle pass.
4)暂停服务时分跨越式30天
4) Over 30 days of downtime
将蒸汽管道中的uvuv墨水排净。参与提液提炼剂在旋转一时，疏浚因永劫间暂停服务而梗塞的蒸汽管道。提液提炼剂在旋转时可终🥀止连续分之五钟的雾炮买通。提液提炼剂在旋转终了后排净蒸汽管道，参与新uvuv墨水，再买通雾炮3钟头使墨线社会价值六倍🦩相同。
Empty the ink in the pipeline. Add diluent and run for one hour to dredge the blocked pipeline due to long shutdown. When the diluent is running, the nozzle can be opened for 5 minutes at a time. After the diluent is running, the drainage pipe is emptied, new ink is added, and the nozzle is opened for 3 minuಞtes to make the ink line position more stable.
5) 喷码器保护英文怡养周期长。 每五天对喷码器管线退出多次查抄，就是是损坏、座谈会就是是晃动 改换活性炭过滤系统。该控制视自然的环境而定，如烟尘较少最低每过4个月时间改换多次，寻常自然的环境下不得每过18个月时间退出多次。自动化设备外界排尘。该控🔯制最低不得每过5个月时间退出多次。
5) Maintenance cycle of jet printer. Every 15 days, check the pipeline of the jet printer, whether it is ageing, whether the joints are loosened and the fi🦂lters are replaced. The operation depends on the environment. If the dust is large, it should be replaced at least every four months. Norma🍒lly, it should be done every 12 months. Dust removal inside the machine. The operation should be performed at least once every 1 month.
四、打码机材料的利用和存有重视起来事变
IV. Notices for Use and Maintenance of ᩚᩚᩚᩚᩚᩚᩚᩚᩚ𒀱ᩚᩚᩚConsumables for Printers
1、手持喷码机通过的耗损品挥发物性强，保管时，应远低于35度，可以防止低温制冷的效果，阔别多年火灾、热力，就必须填(t💖ian)料密封典范并贮藏在荫凉通风处（封(🎃feng)闭性好的厚壁铁柜内存放）。
1. The consumables used in the jet printer are highly volatile. They should be kept below 35 degrees, avoid high temperature and keep away from fire and heat sources. They must be well sealed and 🌠stored in a shady an♓d ventilated place (in a thick-walled iron cabinet with good sealing).
2、手持喷码机的耗损品的存放期是几年。
2. The shelf life of con🧸sumables of jet printer is one year.
3、喷码(ma)器的耗损品严酷匹配加盟品牌凭借，不准凭借替换成品，不是会给史诗装备组成严峻(🎉jun)形势快消失。
3. The consumables of the jet printer should be strictly used in accordance with the brand, and no substitute should be used, otherwise serious damage♏ will be caused to the equipment.